This driver is big - like, really big - so it's easy to send drives right down the middle. With the most MOI ever in a Cleveland Golf driver, Launcher XL will have you thinking less about the club in your hands and more about carrying bunkers, clearing hazards, and finding the fairway.
It’s called the XL Driver for a reason. Mainly because it’s really big and so is the sweet spot. That makes it extremely forgiving. We packed the XL Driver with MOI for towering drives that fly straight.
XL HEAD DESIGN
This is huge: a bigger head means an MOI of 5,200 g-cm – our most ever in a Cleveland Golf driver. Add that forgiveness to a high launch from low-and-deep weighting, and you’ll enjoy maximum distance with maximum fun.
REBOUND FRAME
What’s better than one flex zone? Two (duh). Alternating zones of flexibility and rigidity direct more energy into the golf ball for increased ball speed and distance on every shot.
ACTION MASS CB
An 8g weight placed inside the end of the grip delivers better balance for more control without extra effort.
ADJUSTABLE HOSEL
Adjust your loft from 9 to 12 degrees to optimize your launch angle, distance, and shot shape. Loft can be adjusted at 0.5 deg increments with 12 positions in all.
ACCURACY BUILD
If precision is your top priority, this custom configuration is an inch shorter without counterbalancing for max control off the tee.
LAUNCHER XL DRIVER SPECS
| LOFT | HEAD SIZE | LIE ANGLE | STANDARD BUILD LENGTH | STANDARD BUILD SW | ACCURACY BUILD LENGTH* | ACCURACY BUILD SW* | HAND |
|---|
| 9° | 460cc | 58.5° | 45.75" | D3 | 44.75" | D0 | RH/LH |
| 10.5° | 460cc | 60.0° | 45.75" | D3 | 44.75" | D0 | RH/LH |
| 12° | 460cc | 58.5° | 45.75" | D3 | 44.75" | D0 | RH/LH |
*Accuracy build is a featured, preconfigured custom option for players who seek maximum control. Head/shaft/grip are the same, but length is 1” shorter and 8g grip weight is excluded.
PROJECT X CYPHER 50 SHAFT
| TIP DIAMETER | WEIGHT (g) | LAUNCH | SPIN | FLEX |
|---|
| 0.335" | 52(A), 54(R), 56(S) | Mid-High | Mid-High | 5.0-A, 5.5-R, 6.0-S |
GOLF PRIDE TOUR VELVET 360
| INSIDE DIAMETER | WEIGHT (g) |
|---|
| 58 ROUND | 52 g |
12 DRIVERS IN 1?
HOSEL SLEEVE ADJUSTABILITY GUIDE
The Launcher XL Driver comes standard with an adjustable hosel sleeve that adjusts from 9.0° to 12.0° in 0.5° increments. In all, there’s 12 different positions which means you’re bound to find the perfect setup for your swing.
The 4 primary loft settings are marked on the sleeve at 9.0°, 10.5°, 12.0° and 10.5° Flat. The varying settings between each are visible on the pre-installed shaft tip.
BALL LAUNCHING TOO LOW?
INCREASE LOFT UP TO 12 DEGREES.
BALL LAUNCHING TOO HIGH?
LOWER LOFT DOWN TO 9 DEGREES.
Adjusting the driver’s loft also has a slight impact on your face and lie angles. The chart below will help you decide which configuration is right for your swing. Side note: it’s also a great conversation starter next time you’re trying to impress your father-in-law.
UNIVERSAL TORX 25 WRENCH
USE ONLY THE CUSTOM TORQUE WRENCH WHEN MAKING HOSEL ADJUSTMENTS.
HOW TO REMOVE AND INSTALL QTS SLEEVE (TORQUE WRENCH OPERATION)
1.Hold the club upright with the grip resting on the ground.
Use this position when loosening and tightening.
2.Supporting the head in your hand, gently insert the torque wrench into the screw hole.
Shaft and torque wrench should form a straight line
Improperly aligned torque wrench
3. Loosen
With the torque wrench aligned with the shaft, turn it counterclockwise.
*Shaft will come off without loosening the screw too much.
4. Tighten
With the torque wrench aligned with the shaft, turn it counterclockwise.
*Always tighten until you hear a 'click'. Failure to do so may result in separation of the club head or product damage.
5. Insert the shaft into the head
Align the position line with the LOFT and press straight in.
*Illustration shows 10.5
6. QTS setting examples
FOR 9.0° OF LOFT
Align the LOFT on the head with 9.0° on the QTS Sleeve and press straight in
FOR 12.0° OF LOFT
Align the LOFT on the head with 12.0° on the QTS Sleeve and press straight in
IMPORTANT PRECAUTIONS
To ensure a safe and satisfying golfing experience, please be sure to follow these Important Precautions.
Be sure to read the Important Precautions carefully and exercise appropriate care. The manufacturer assumes no liability for injury or product damage due to failure to comply with the instructions herein.
RULES OF GOLF
It is against the rules to modify club performance during a round by changing the QTS sleeve position or exchanging weights to change the CG position, as this breaches the Rules of Golf regulation 4-2a, which states: "During a stipulated round, the playing characteristics of a club must not be purposely changed by adjustment or by any other means."
BEFORE USING
Check to see that the QTS sleeve is properly secured.
Tighten until you hear a 'click'. If you fail to properly secure the sleeve, there is a possibility that the head may come off mid swing, injuring either you or a bystander.
Cleveland Golf Launcher XL Adjustable Driver
